How To Fix A Faucet That Is Leaking From The Neck

Today I'm going to be showing you how to repaira leaking high-rise faucet.

It's showing it's leaking at the neck here.

See all the watercoming out? That's not right.

It's going to be leaking down below, and we don't want that.

Anyway, for this repair, we don't need to turn the water off.

If you have a single handlefaucet, for that type of repair you would need to turn the water off.

A lot of times,this one you can do by hand, this one here.

Just turn it out.

If you did need to use a pair of channel locks,you're going to want to protect your jaws with tape like so, to prevent marring theneck here.

You also could use a strap wrench for this, which is a lot better than channellocks.

Because channel locks could deform the neck if you were to squeeze it too tight,it could deform or reshape the neck as well as mark it up.

But a strap wrench kind of grabs it, tightensdown and you can cinch it down and turn it out.

But anyway, this one we can do by hand.

Inside here, there's three O-rings, and these are the O-rings that we're going to need toreplace here.

Now I already know my sizes of O-rings that I need, but if you don't knowwhat sizes you need, they do sell an O-ring kit.

The stuff that I'm going to be usingis pretty stinky.

It's this faucet grease here, and if you getit on your hands, it's pretty tough to wash off.

Because it's a high temperature faucetgrease and it's meant to not wash off with water.

When you go to repair this, you'regoing to want to wear gloves, and a good way to do this is to wear two or three pairs ofthese disposable gloves.

You'll see reason I do this is this stuff'sso smelly.

What you can do is unwrap the glove, one of the gloves, in order to use your toolsand not get the faucet grease all over your tool.

Not get the faucet grease all over theoutside of the faucet.

This faucet is going to be in need of some cleaning afterwardsanyway, but that's another story.

The easy way to get these O-rings off is touse a small flathead screwdriver.

I've got one in my Leatherman, so it comes in handyfor this.

And it's just a matter of picking these off, fairly simple.

If you keep themtogether, you can use that to size up your new O-ring to make sure you're getting theright size.

And all three of these are the same size, so you really only need to keepone together so if you needed to cut it, you could.

Not a big deal.


One, two, three O-rings,another reason for the gloves there.

Now what you want to do is coat this so that underneathit, it'll have a coating of the faucet grease.

This stuff can be a little tricky to get apartsometimes, and mine's getting kind of old.

It's time to order some more faucet grease.

So anyway, go underneath where your O-rings are going to go.


Now we'll slip ournew O-rings on.

Here's the first one.

Yeah, the gloves are going to make it a little tricky,but it's what it is, job security.

There's the second one, and number three.

Now we're going to coat the outside of the O-rings with the faucet grease.

This is ahigh temperature faucet grease, so it's not going to come off with hot water, and lubingthis all around is going to prevent our O-rings from pinching up inside there.

Because if they pinch then they're going tobreak, and then your faucet's going to leak.

Okay, now that we got that, this is the goodtime to go ahead and remove that outer layer of the gloves.

We can dispose of those.

Nowwe're ready to put our faucet neck back together.

So we can slip this up, and then push it inall the way around gently, and then go ahead and slowly hand thread this in place so thatwe don't get it cross-threaded.

We can get rid of these, and we're just going to handtighten this down.

Once that's nice and tight.

And now once that's nice and tight, just handtightened, we're going to prove it and check for any leaks.

Now if we see any leaks here, then can useour channel locks to tighten it up a little bit more, but it looks like everything's goodhere, no leaks.

So now you want to check underneath for anyleaks, and you'll need to remove your gloves to do that.

I'm going to take these off nowand check for any leaks down below.

Now first, you want to take your rag, dry everythingoff.

It looks like we've got a loose handle there also.

I'll show you how to tighten thatup, it's just an Allen wrench under here, it's real easy, but that's another story.

I may put out another video how to tighten those down.

I can try to put the link on thevideo here.

Going to come down below the sink and feelall around for any leaks.

Now, you may have to dry everything off and check this the followingday, as it was leaking before.

So you probably have some water that's still trapped insidethere, so you're going to have to just keep an eye on this, and do what you can to dryit out.

Then go ahead and turn the water on.

If yousee a flood of water, you know you've got a problem you've got to deal with.

But ifyou're just feeling a little bit of moisture from before, you're actually okay.

An old trick is after you dry everything upbelow, is to put paper towels down, or toilet paper in order to check it.

Wow, there's somethingwrong here, someone skipped the air gap, that's not good for the dishwasher.

You don't wantto do that.

Skipping that air gap can make you reallysick, because the air gap prevents the sewer gases from going into your food when it passesfrom your disposer, so you definitely don't want to run it straight in like this.

This is wrong.

So if you see this, you definitelywant to install an air gap to prevent getting harmful bacteria and everything into yourdishwasher.

Anyway, that's another story also.

Anyway, if we have no leaks here we're allset, good to go.

One fixed high-rise kitchen faucet.

Good to go.

Source: Youtube

Also read: Remarkable Ideas Of Cheap Balcony Ideas

How To Fix A Faucet That Is Leaking From The Neck



See also: Bedroom Furniture Sets King Platform So as to create a home environment that expresses your unique personality and style, you first have to recognize what styles you admire, which of them complement each other, and avoid those that do not play nice together. If you want to redesign your home, but are not sure how to start, you should first subside on the style of inside design best suited you best. At the start of any interior design task, we wonder in what style should we create our home in order to feel good in that environment. And when I say OUT OF the BOX, I dont actually mean go crazy, I simply suggest that you take some steps to design the sort of home that you really want or the actual design process so that you have been in awe of your wondrous creativity. Regardless of whether your style is modern, traditional or rustic, Shutterfly home decor lets you decorate your space with unique, personal designs. Because with any specific style, you run the risk of your home looking over inspired rather than tasteful and interesting.
Minimal textures and strong geometric forms, neutral colours accented with a single bold colour along with polished finishes and irregular in shape balance are key discovering features of modern style interiors. A word that is commonly used to describe modern style is sleek, and there is not a lot of clutter or accessories involved with a modern style. The style is contemporary modern style but keeps a hotline through chosen finishes and color range used. You should remember that designers blend different elements from many decorating styles together, but the essential thing is to identify the core aspects of each one. Soft modern interiors are characterized by neutral elements accentuated by bold color, or attractive elements, such as beading and glass, but the focus is always the basics of line, form and form. Take elements of your preferred style and make your design so that you avoid over doing it. When it comes to modern-day style, essential things are smooth, clean and geometric shapes and flexural lines. Line can be used through the use of bold colour blocks, high ceilings, square edged furniture, linear wooden floors, floor mats, bare windows and geometric shapes in wall structure art and sculpture.